A 5 pack of Molex 2mm pitch plug shells and crimp terminals (each packet contains 5 spare crimps for you to practice).

A 5 pack of Molex 2mm pitch socket shells and crimp terminals (each packet contains 5 spare crimps for you to practice).

A 100mm lead with a Molex 2mm pitch plug (male shell, female pins) at one end and bare wires at the other end. The wire choice is 0.1mm sq (2A) or 0.15mm sq (4A).

Wire Colours:

Pins	Colour
2	1=Black, 2=Red
3	1=Black, 2=Yellow, 3=Red
4	1=Black, 2=Blue, 3=Yellow, 4=Red

#pins:	2 Pin Plug Lead 100mm £0.00 3 Pin Plug Lead 100mm +£0.30 4 Pin Plug Lead 100mm +£0.65
Wire Size:	0.1mm (2A max) £0.00 0.15mm (4A max) +£0.20

A 100mm lead with a Molex 2mm pitch socket (female shell, male pins) at one end and bare wires at the other end. The wire is 0.15mm sq and good for 4A.

Wire Colours:

Pins	Colour
2	1=Black, 2=Red
3	1=Black, 2=Yellow, 3=Red
4	1=Black, 2=Blue, 3=Yellow, 4=Red

#pins:	2 Pin Socket Lead 100mm £0.00 3 Pin Socket Lead 100mm +£0.30 4 Pin Socket Lead 100mm +£0.65
Wire Size:	0.1mm (2A max) £0.00 0.15mm (4A max) +£0.20

A 2 pin Molex plug fixed into a 20x10mm mounting plate and with 100mm leads plus a mating 2 pin socket with 100mm leads. The 0.1mm sq wire is OK up to 2A and the 0.15mm up to 4A.

Wire Colour:

2 x black 0.1mm £0.00 red & black 0.1mm £0.00 2 x black 0.15mm £0.00 red & black 0.15mm £0.00

All of these adapters use the Micron wiring convention (pin 1 is negative). Please contact us if you need an adapter lead with pin 1 connected to positive.

An adapter lead to allow single cell LiPo with 'UM' battery connector to be used with receivers or ESC that have a Molex 2mm 2 pin socket. The Molex plug is wired with the Micron convention of pin 1 negative.

An adapter lead to allow single cell LiPo with a 2 pin Molex 2mm battery connector to be used on receivers with a 'UM' socket (e.g. the Spektrum AR6410), or to allow the LiPo to be charged with a 'UM' charger. The Molex socket is wired with the Micron convention of pin 1 negative.

A 250mm 1S charge lead with a 2 pin Molex 2mm pitch socket at one end and a red/black 4mm plugs at the other end for connection to a chargers's positive/negative sockets. For use with 1S switch plates.

A 250mm charge/balance adapter lead with a Molex 2mm pitch plug at one end and a JST-XH plug at the other end plus 200mm red/black bare end wires for connection to a charger's positive/negative sockets. The red/black wires may be snipped off if your charger uses only the JST-XH connector for charging and balancing. If your charger does require connection to the charge sockets, suitable 4mm plugs are available.

The adapter is designed for charge currents up to 2A.

The Molex 2mm connector is used for LiPo charging and balancing where space is tight and there would be insufficient space for a JST-XH. These connectors are used on the Model Rail Wiring Harnesses.

Price: from £3.50

These switch/charge modules provide a simple way to implement an on/off switch and charge connector on your model vehicle. They comprise a small GRP plate containing a slide or toggle switch plus a Molex 2mm pitch plug (male plastic shell, female metal parts) and an LED which may be used to monitor the receiver status. The GRP plate is supplied without any mounting holes as it may be either glued into place or holes made and fixed with small (e.g. M2) screws.

The switch modules may be used for any battery type. Lithium batteries (LiPo or LiIon) require one more charge wire than the number of cells so you must select the correct 'S' count for your battery. NiMH batteries need only a 2 wire charge connector so select 1S for these.

An adapter lead will be needed to connect the switch module to your charger:

NiMH or 1S:	Molex 2mm 2 Pin Charge Lead (1S)
2S ... 4S	Molex 2mm to JST-XH Charge Lead

A tiny on/off slide switch and charge socket module for model vehicle installation, comprising micro slide switch 2mm pin space Molex charge connector and 1.8mm LED mounted on a 20mm x 10mm GRP plate.

Price: from £5.15

A small on/off switch and charge socket module for model vehicle installation. The 1S module is suitable for a single LiPo/LiIon cell or a multi-cell NiMH battery. The 2S, 3S and 4S modules are for multi-cell LiPo/LiIon batteries which require all cells to be connected to an external balancing charger.

The module comprises a miniature toggle switch, 2mm pin space Molex charge connector and 1.8mm LED mounted on a 25mm x 15mm GRP plate. The plate may be glued into place or drilled for mounting screws. The image shows the 1S version with a 2 pin connector, the 2S, 3S and 4S versions have 3, 4 and 5 pin connectors. A charge lead is required to connect the module to your charger: for 1S or for 2S, 3S and 4S.

The wiring comprises:

• a Molex 2mm, JST-XH or JST-RCY battery connector on a 50mm lead; the JST-RCY is suitable only for the 1S module
• 100mm red/black/orange wires with bare ends for soldering onto your receiver pos/neg/LED2 pads or splicing onto the receiver lead-out wires. The LED positive wire (brown) has a series resistor for use on 3.3V (Deltang Rx 'P' output)

Price: from £6.10